|
DESCRIPTION : Bio Aqua Enamel Lacquer is a dirt-and
water-repellent,gloss or matt painted finish, containing no toxic
solvents, resins or heavy metals. It is suitable for use on toys,
paneling, skirting boards, architraves, doors and windows.
PREPARATION : Prepare the surface in accordance
Australian Standard 2311 Painting of Buildings. Do not apply
coatings to unseasoned or wet timber. Surfaces
and already painted surfaces in gloss or semi glass paint should
be well sanded, dry and cleaned of greasy, waxy and dirty
contaminants using BIO Thinner. Round off sharp edges. It is
also good practice to prime back surfaces. Hardwoods and
other timbers rich in natural oils, waxes, acids and terpenes
should be degreased using Bio Thinner because these substances may
mix with the paint and prolong its drying time. Imperfect coatings
may require complete stripping before applying BIO products. Timber
moisture content must be under 15% for softwood, and under 12% for
hardwood. Fill imperfections and cracks with a suitable filler.
Application: Stir thoroughly before use with a broad flat
stirrer.. Apply one coat of Undercoat and two coats of topcoat.
Minimum dry film thickness is 100 microns. Maintain a wet edge when
painting. Best results are achieved using thin coats. Thick coats
will cause runs to appear.
METAL PRIMER : Provides anti-corrosive protection for
steel, aluminum, brass and copper. Not effective on zinc and
galvanized surfaces. The metal should be cleaned of all grease,
dirt, processing soil, salt residues, weld scale, rust and other
residue which is likely to affect the performance of a protective
coating. Apply 1-2 coats of Metal Primer thinly and evenly. Lightly
sand between coats when completely dry. Finish with Bio Enamel
Lacquer, white or coloured.
DRYING : Drying time on a day of around 25 C is
approx. 2-4 hours. During cold and humid weather allow longer
drying time Apply second and subsequent coats only after
previous coat has thoroughly dried. Do not be tempted to apply
paint too thickly, as this retards the drying process. Lightly sand
if necessary after the undercoat. Do not use below +12C and above
80% humidity, in cold damp conditions, when condensation, rain, dew
or frost are likely to occur or hot days, direct sunlight or hot
surfaces. Provide adequate ventilation during application and
drying. Avoid steam and condensation for 48 hours. Reaches maximum
durability after 8-14 days.
COLOURS : Bio Enamel Lacquer and Undercoat are supplied
in base white. The white based top coat can be tinted with BIO Pigments water based. The
customer tints to his/her satisfaction. All colours are
intermixable. Note: slight variations between lots are possible
CLEANING : Use soapy warm water and/or BIO
Thinner.
COVERAGE : 1 Liter covers 10-12 sqm., depending on the
absorbency of the substrate.
PACKAGING : White and Undercoat : 250ml, 1 and 5
Litres
INGREDIENTS :Based on plant oil, water, lecithin, lead
free drying agent, titanium dioxide, calcium carbonate, iron oxide,
china clay, metal and mineral pigments, borax. Free of cadmium,
chromates and lead.
STORAGE : Keep tightly sealed in a cool, dry and
frost free place. Surface skin may develop in opened cans.
PRECAUTION : Keep away and out of the reach of children.
Please dispose used rags in a sealed metal container. Can
spontaneously combust.
PAINT DISPOSAL: Do not pour left over paint down the
drain. Unwanted paint should be brushed out on newspaper, allowed
to dry and then disposed of via domestic waste collection. Let
empty container dry out as well and dispose via recycling
program.
The preceding information was prepared by BIO Products Australia
and is given as a general guide only. Some variations may occur or
be advisable for particular conditions. The manufacturer’s
responsibility for claims arising from breach of warranty,
negligence or otherwise is limited to the purchase price of the
material.
BIO ENAMEL LACQUER WB is an environmental friendly
product.
1/08/2007
BUY NOW from ONline
Store (Pigments)
BUY NOW from Online Store
(Undercoat)
view pdf version
(84K)
| 