|
DESCRIPTION: Bio Enamel Lacquer is a thick,
dirt-repellent and water-repellent, gloss or satin painted finish,
containing no toxic solvents, resins or heavy metals. It is
suitable for all wood types, steel, aluminum and copper. Especially
suitable for use on toys, paneling, skirting and architraves,
garage doors and window frames.
PREPARATION: Prepare the surface in accordance Australian
Standard 2311 Painting of Buildings. Do not apply coatings to
unseasoned or wet timber. Surfaces should be well sanded, dry and
cleaned of greasy, waxy and dirty contaminants using BIO
Thinner. Round off sharp edges. Hardwoods and other
timbers rich in natural oils, waxes, acids and terpenes should be
degreased using Bio Thinner because these substances may mix with
the paint and prolong its drying time. Imperfect coats may require
complete stripping before applying BIO products. It is also good
practice to prime back surfaces. Timber moisture content must
be under 15% for softwood, and under 12% for hardwood.
APPLICATION: Stir thoroughly before use with a broad flat
stirrer. Thin as desired with 5-10% BIO Thinner to obtain a
smooth flowing consistency. Apply one coat of Undercoat and two
coats of topcoat. Minimum dry film thickness is 100 microns.
Maintain a wet edge when painting.
METAL PRIMER: Provides anti-corrosive protection for
steel, aluminum, brass and copper. Not effective on zinc and
galvanized surfaces. The metal should be cleaned of all grease,
dirt, processing soil, salt residues, weld scale, rust and other
residue which is likely to affect the performance of a protective
coating. Apply 1-2 coats of Metal Primer thinly and evenly. Lightly
sand between coats when completely dry. Finish with Bio Enamel
Lacquer, white or coloured.
DRYING : Apply second and subsequent coats only after
previous coat has thoroughly dried. This will take between 24 and
40 hours, and longer with cold or damp weather. Do not be tempted
to apply paint too thickly, as this retards the drying process.
Lightly sand if necessary after the undercoat. Do not use below
+12C and above 80% humidity, in cold damp conditions, when
condensation, rain, dew or frost are likely to occur, or hot days,
direct sunlight or hot surfaces. Provide adequate ventilation
during application and drying. Reaches maximum durability after
8-14 days.
COLOURS: Bio Enamel Lacquer and Undercoat are supplied in
base white. Standard full colours are: Green, Blue,
Ochre, Yellow, Brown, Red and Black. All colours can be used as
tints. The customer tints to his/her own satisfaction. All colours
are intermixable. Note: slight variations between lots are
possible
CLEANING: Use BIO Thinner.
COVERAGE: 1 Litre covers 10-12 sqm., depending on the
absorbency of the substrate.
PACKAGING: White = 250ml, 1 and 5 Litres. Colours = 250
ml, 1 and 2.5 Litres
INGREDIENTS :Based on castor oil, soya bean oil,
safflower oil, pine resin, lemon peel oil, paraffin oil, lecithin,
bentone, ethanol, feldspar, lead free drying agent, calcium
carbonate, talc, dolomite, iron oxide, zinc oxide, metal and
mineral pigments. Free of cadmium, chromates and lead.
STORAGE: Keep tightly sealed in a cool and dry
place. Surface skin may develop in opened cans.
PAINT DISPOSAL: Do not pour left over paint down the
drain. Unwanted paint should be brushed out on newspaper, allowed
to dry and then disposed of via domestic waste collection. Let
empty container dry out as well and dispose via recycling
program.
PRECAUTION: Keep away from open flames and out of the
reach of children. Please dispose used rags in a sealed metal
container. Can spontaneously combust.
The preceding information was prepared by BIO Products Australia
and is given as a general guide only. Some variations may occur or
be advisable for particular conditions. The manufacturer’s
responsibility for claims arising from breach of warranty,
negligence or otherwise is limited to the purchase price of the
material.
BIO ENAMEL LACQUER is an environmental friendly
product.
view pdf version
(83K)
1/08/2007
| 