|
DESCRIPTION: BIO Wood Varnish is a clear
varnish. It is based on natural and non toxic ingredients like
renewable plant oils and resins. The natural and non toxic
ingredients are gentle to the climate and resources. It is a hard,
elastic, semi-transparent varnish for use on timber surfaces
exposed to sun and rain. It is resistant to dirt and moisture.
PROTECTION: Protection against weather and
wood-destroying ultra-violet light. 3 coats are recommended.
Minimum dry film thickness on an even smooth surface: 60 micron,
better 100 micron. Box frames, timber windows, cladding and end
grains must be treated BEFORE INSTALLATION with one coat
of BIO Wood Primer and one
coat of BIO Wood Varnish clear. It is also good practice to
prime back surfaces. Re-apply once the finish appears to become
dull.
PRIMING: For fungi and insect treatment
use BIO WOOD PROTECTING BORAX. Before painting, wipe off the surplus of Borax
with a damp cloth, otherwise surface residue may inhibit paint
adhesion.
PREPARATION: Prepare surface in accordance with
AS 2311 Painting of Buildings. Do not apply coatings to unseasoned
or wet timber. Wood and other surfaces should be well sanded, dry
and cleaned of greasy, waxy and dirty contaminants using BIO
Thinner. Round off sharp edges. Imperfect coats may require
complete stripping before applying BIO products. Hardwoods and
other timbers rich in natural oils, waxes, acids and terpenes
should be degreased using BIO Thinner, because these substances may
mix with the varnish and prolong its drying time. Do not apply on
over acrylic, PUR or epoxy based coatings.
APPLICATION: Stir thoroughly before use with a
broad flat stirrer. Brush thinly and evenly working varnish well
into the grain. Maintain a wet edge when painting. Thick coats
wrinkle when dry. Avoid bubbles. Lightly sand between coats if
necessary with fine sandpaper. Allow 12 to 24 hours to dry between
coats. Low temperatures and humid conditions prolong the drying
time. Apply second and subsequent coats only after previous coat
has thoroughly dried. Do not use below 10°C and or above 80%
humidity, in cold damp conditions, when condensation,
rain, dew or frost are likely to occur or hot days, hot surfaces
and direct sunlight. Provide adequate ventilation during
application and drying. Reaches maximum durability after 8-14
days.
VARIATION OF USES:
RE-COATING: Re-coating is recommended after
approximately 2 or 3 years, depending on the exposure to the
weather.
CLEANING: Clean with BIO Thinner.
COVERAGE: 1 Litre covers approx. 10-12
sqm.
PACKAGING : 1 and 4 Litres.
INGREDIENTS: Based on modified plant oil, wood
oil, rosin, titanium dioxide, mica, silica, bentone, soya lecithin,
UV-protector, paraffin oil, lemon peel oil, pine oil and lead free
drying agents.
STORAGE: Keep tightly sealed in a cool and dry place.
Surface film may develop in opened cans.
PAINT DISPOSAL: Do not pour left over paint down the
drain. Unwanted paint should be brushed out on newspaper, allowed
to dry and then disposed of via domestic waste collection. Let
empty container dry out as well and dispose via recycling
program.
PRECAUTION: Keep away from open flames and out
of reach of children. Do not misuse. Please dispose of used rags in
a sealed metal container. Can spontaneously combust.There is no
manufacturer’s liability for applying this product onto non
compatible paint systems like acrylics, polyurethane, epoxy
finishes etc.
The preceding information was
prepared by BIO Products Australia and is given as a general guide
only. Some variations may occur or be advisable for particular
conditions. The manufacturer’s responsibility for claims arising
from breach of warranty, negligence or otherwise is limited to the
purchase price of the material.
BIO WOOD VARNISH CLEAR is an
environmental friendly product.
1/08/2007
BUY NOW from Online
Store
View pdf
version | 