|
DESCRIPTION: Bio Enamel Lacquer High Solid is a
thick, dirt and water-repellent, gloss or satin painted finish,
containing no toxic solvents, resins or heavy metals. Suitable for
all wood types, steel, aluminium and copper. Especially suitable
for use on toys, paneling, skirting and architraves, garage doors
and window frames.
PREPARATION: Prepare the surface in accordance
Australian Standard 2311 Painting of Buildings. Surfaces should be
well sanded, dry and cleaned of greasy, waxy and dirty contaminants
using BIO Thinner. Do not apply coatings to unseasoned or wet
timber. Round off sharp edges. It is also good practice to prime
back surfaces. Hardwoods and other timbers rich in natural
oils, waxes, acids and terpenes should be degreased using Bio
Thinner because these substances may mix with the paint and prolong
its drying time. Imperfect coats may require complete stripping
before applying Bio products. Timber moisture content must be under
15% for softwood, and under 12% for hardwood.
METAL PRIMING: Provides anti-corrosive protection
for steel, aluminium, brass and copper. Not effective on zinc and
galvanized surfaces. The metal should be cleaned of all grease,
dirt, processing soil, salt residues, weld scale, rust and other
residue which is likely to affect the performance of a protective
coating. Apply 1-2 coats of Metal Primer thinly and evenly. Lightly
sand between coats when completely dry. Finish with Bio Enamel
Lacquer white or coloured
APPLICATION: Stir thoroughly before use with a
broad flat stirrer. Thin as desired with 5-10% BIO Thinner to
obtain a smooth flowing consistency. Apply one coat of BIO Enamel
Lacquer Undercoat and two coats of top coat. Minimum wet film
thickness for each coat must be 100 microns. Maintain a wet edge
when painting.
DRYING: Apply second and subsequent coats only
after previous coat has thoroughly dried. This will take between 24
and 40 hours, and longer with cold or damp weather. Do not be
tempted to apply paint too thickly, as this retards the drying
process. Lightly sand if necessary. Do not use below +12C and above
80% humidity, in cold damp conditions, when
condensation, rain, dew or frost are likely to occur or hot days,
direct sunlight or hot surfaces. Provide adequate ventilation
during application and drying. Reaches maximum durability after
8-14 days.
COLOURS: Currently only available in White.
Customer can tint to his/her own satisfaction with BIO Enamel
Lacquer (solvent based) Interior colour range.
INGREDIENTS: Based on Castor oil, tung oil, pine
resin, lemon peel oil, paraffin oil, lecithin, bentone, ethanol,
lead free drying agent, talc, feldspar, iron oxide, metal and
mineral pigments. Free of cadmium, chromates and lead.
CLEANING: Use BIO Thinner.
COVERAGE: 1 Litre covers 8 – 10 sqm. Depending on
the absorbency of the substrate.
PACKAGING: White only: 1 and 4 Litres
PRECAUTION: Keep away from open flames and out of
the reach of children. Please dispose used rags in a sealed metal
container. Can spontaneously combust.
PAINT DISPOSAL: Do not pour left over paint down
the drain. Unwanted paint should be brushed out on newspaper,
allowed to dry and then disposed of via domestic waste collection.
Let empty container dry out as well and dispose via recycling
program.
STORAGE: Keep tightly sealed in a cool and dry
place. Surface skin may develop in opened cans.
The preceding information was prepared by BIO Products Australia
and is given as a general guide only. Some variations may occur or
be advisable for particular conditions. The manufacturer’s
responsibility for claims arising from breach of warranty,
negligence or otherwise is limited to the purchase price of the
material.
BIO ENAMEL LACQUER HIGH SOLID Interior/Exterior is an
environmental friendly product.
View pdf version (94K)
1/08/2007 | 