|
DESCRIPTION: VOLVOX ProAqua Transparent Wood Finish
is V.O.C. free, water based, non-drip, and long lasting wood finish
for interior and exterior use. Available in transparent wood
colours of Natural (exterior only) Clear (interior only), Pine,
Walnut, Oak, Mahogany, Teak, White, Ebony, Citrus, Yellow, Corn
Yellow, Oriental Red, Meadow Green and Mondrian Blue. The ProAqua
Clear can be tinted to match your individual colour scheme.
USE: VOLVOX ProAqua Transparent Wood Finish can be
used on windows, doors, pergolas, timber cladding, and other wood
that should be protected interior and exterior. Depending on the
pigment concentration it can appear transparent up to opaque. If
you decide for clear finish on the exterior, use VOLVOX ProAqua
Natural No. 2-362. VOLVOX ProAqua Transparent Wood Finish is not
recommended to be used on timber floors. Use VOLVOX Hard Oil Wax
Finish, VOLVOX Wood Oil or VOLVOX Hard Oil instead.
ENVIRONMENT: VOLVOX ProAqua Transparent Wood Finish
is made from natural and non-toxic raw materials. Manufacturing
process ensures ecological sustainability and avoids water
pollution. No chemical solvents are used. The product will not
charge electro static energy. When used according to manufacturer’s
direction, the product can be considered as harmless to human and
the environment. Certified V.O.C. free (TüF Essen 3.2-3/02).
SURFACE PREPARATION: Provide a clean, dry, firm and
grease free surface. Timber should be in good physical shape and
absorbent. Oil, resin and tannin reach wood should be cleaned using
appropriate methods. Slightly sand and check old coats of VOLVOX
ProAqua Transparent Wood Finish if these are fit to be painted
over, remove them if they are not.
APPLICATION: Reduce VOLVOX ProAqua Transparent Wood
Finish with 5-10% water. Stir well and apply and spread evenly. Use
lacquer roller and/or paint brush and/or airless or Aircoat spray
applicator. Let dry for at least one hour, then sand slightly
(120-180 grid). Second coat can be applied undiluted, reduce with 5
– 10 water if necessary. After drying, sand again. For exterior
wood protection, at least three coats are recommended. Do not apply
in temperatures below 10°C or above 30°C.
DRYING AND RECOATING: Depending on temperature and
humidity, touch dry within 15 minutes, dry to sand and repaint
after 1 hour.
COVERAGE: Depending on surface condition 0.75 litre
for approx. 10 m²2.5 litre for approx. 33
m²per coat
CLEAN UP: Clean tools with soapy water after use
away from drains.
INDIVIDUAL TINTED VOLVOX ProAqua: The Clear
VOLVOX ProAqua Transparent Wood Finish can be tinted by adding
pigment pastes according to NCS Standards. Please contact your
VOLVOX Dealer to obtain more information.
MAINTENANCE: Check vanish from time to time for
aggressive pollution deposits and clean when necessary. If water
repels, that’s an indication that the VOLVOX ProAqua Transparent
Wood Finish is intact, if it doesn’t its time to rejuvenate. Clean
surface and slightly sand then simply apply another coat.
STORAGE AND SHELF LIFE: Store tightly sealed in a
cool and dry place. Minimum shelf life for unopened and properly
stored cans is 24 months. Protect against freezing.
INGREDIENTS: Water, earth pigments, mineral filling
materials, vinegar ester, preservatives.
SAFETY: Provide adequate ventilation during and
after application. Even if non-toxic, keep away from children.
DISPOSAL: Allow unwanted paint to dry. Solid matter
should be disposed of via the normal garbage collection
service.
The preceding technical information sheet was prepared by Amma
Earth Australia and is intended to provide guidelines for users.
Volvox products are guaranteed to give satisfactory performance
only if used as recommended. Liability shall be limited to refund
of purchase price or the replacement of a defective product. There
are no other warranties expressed or implied.
Disclaimer: It is recommended to test the product on
the intended surface to ensure its suitability.
Made in Germany.
August 2006
view pdf version
(77k)
| 