|
Range of application: For interior and exterior iron and
steel surfaces; also suitable for radiators and heating pipes.
Technical qualities: Good adhesion and coverage on metal.
Silky gloss finish. Remains elastic and temperature resistant up to
90 °C (194°F). Contains no lead or chromates.
Full declaration: zinc phosphate, mica, linseed oil -
stand oil - natural resin ester, orange oil, mineral pigments,
Isoaliphates, chalk, castor oil, talcum, silicic acid, drying
agents free of lead, soy lecithin and citron oil.
Colors: 051 persian red, 211 grey white.
Dilution: SVALOS Thinner No. 222, or for spray
application SVALOS Spray Thinner No. 293.
Application method: Sparing brush, spray or roller
application at temperatures over 12 °C (53,6°F) and in dry
weather.
Coverage: 1 undiluted liter (1.06 fl. quart.) is
sufficient for approximately 12 - 18 m2 (129 - 194
ft2) per coat, i.e. 67ml/m2. Coverage could
be considerably higher depending upon the condition and absorbency
of the surface. Always do a test application! The optimal dried
thickness of each coat is 40 - 50 um.
Drying time: At 23 °C (73°F) and 50 % relative humidity,
dry to the touch after approximately 6 hours. Subsequent coats may
be applied after approximately 24 hours.
Cleaning up: Clean equipment immediately after use with
SVALOS Thinner No. 222 or LEVO Brush Cleaner No. 997.
Specific gravity: Approximately 1.5 g / ml.
Safety advice: Provide enough ventilation after
application. Always be sure to store cleaning cloths, sponges, etc.
that are still wet or even slightly moist with DURO No. 623 in an
airtight metal container or in water, due to danger of spontaneous
combustion that could be caused by linseed oil content.
The product itself will no combust spontaneously. Color
discrepancies are possible due to the raw materials. Use the same
batch number per project! Avoid release to the environment.
Refer to special instructions/safety data sheet
Disposal: According to local regulations.
Container sizes: 0,125l; 0,375l; 0.75l; 2,5l; 5,0l; 30
l
Storage: Cool and dry. Shelf life: unopened at least 2
years. Close lid tightly after use and use up within 3 months.
How to use DURO Natural Rust Preventive Primer No.
623
Iron and steel preparation: Remove rust completely.
Surface must be dry and free of separation agents, grease and
dust. Do not use any rust conversion products!
Coating format: Stir DURO Natural Rust Preventive Primer
No. 623 thoroughly before use. Apply base coat of DURO Natural Rust
Preventive Primer No. 623 thinned with 5 - 10 % SVALOS Thinner No.
222 with brush, roller, or spraying device. Sand in between with
220-grain sandpaper not earlier than 24 hours after application.
Apply a sparing, undiluted second coat of DURO No. 623. In exterior
areas, a subsequent treatment of the surface with VINDO Natural
Gloss Paint No. 629 must follow within a week. In interior areas
depending on the field of application, a final coat may be applied
of AIDU Natural Radiator Paint No. 624, CANTO Natural White Satin
Paint No. 625, CANTO Natural Matt Paint No. 692 or VINDO Natural
Gloss Paint No. 629.
Zinc preparation interior: A thorough cleaning of the
surface to ensure adhesion is necessary: e.g. create a solution of
5 liters of water, 1/4 liter of a 25 % solution of
ammonia with a tablespoon of a wetting agent ( such as a dish
washing detergent ), then scrub the surface with a corundum fleece
such as Scotch Brite, do not use steel wool or a wire brush under
any circumstances. A grey foam will develop after 10 minutes of
scrubbing, rinse off thoroughly with water. Wear rubber gloves
while mixing solution and scrubbing. Before treating with DURO, the
surface must be completely dry.
Coating format: Follow coating format as for iron and
steel above. Previously varnished zinc surfaces should not be
painted over with DURO Natural Rust Preventive Primer No. 623.
Important tips: The Color tone might vary from batch to
batch du to the raw materials used. DURO Natural Rust Preventive
Primer No. 623 contains little solvent, so it tends to develop a
skin. Before using, simply remove the skin and stir well. Apply
coating only to thoroughly de-rusted surfaces immediately after the
de-rusting procedure. Transfer unused portion of product into a
smaller container for storage.
BUY NOW from Online
Store
View pdf version (109K)
These directions are the result of long years of research and
practical testing. They are backed by our most current expert
information. New findings may invalidate this information. This
data sheet is meant to serve as information and instruction. No
legal liability should be interpreted from it. In case of doubt,
please contact the retailer, wholesaler, or manufacturer. | 