|
DESCRIPTION: BIO Wood Varnish is a varnish and stain in
one product. Earth minerals, natural oils and resins are the basic
ingredients which makes it a beautiful coloured finish. The natural
and non toxic ingredients are gentle to the climate and resources.
It is a hard, elastic, semi-transparent varnish for use on timber
surfaces exposed to sun and rain. It is resistant to dirt and
moisture.
PROTECTION: Protection against weather, wood-destroying
ultra-violet light is determined by pigment density. In areas of
greater exposure 3 coats are recommended to build up pigment
density or 1 coat of Bio Wood Primer plus 2 coats of Bio Wood
Varnish. Minimum dry film thickness on an even smooth surface: 60
micron, better 100 micron. Box frames, timber windows, cladding and
end grains must be treated with BIO Wood Primer and one coat of BIO
Wood Varnish BEFORE INSTALLATION. It is also good practice to prime
all back surfaces. Reapply once the finish appears to become
dull.
PREPARATION: Prepare surface in accordance with AS 2311
Painting of Buildings. Do not apply coatings to unseasoned or wet
timber. Wood and other surfaces should be well sanded, dry and
cleaned of greasy, waxy and dirty contaminants using BIO Thinner.
Round off sharp edges. Imperfect coats may require complete
stripping before applying BIO products. Hardwoods and other timbers
rich in natural oils, waxes, acids and terpenes should be degreased
using BIO Thinner, because these substances may mix with the
varnish and prolong its drying time. Do not apply over acrylic, PUR
or epoxy based coatings.
APPLICATION: Stir thoroughly before use with a broad flat
stirrer. Brush thinly and evenly working varnish well into the
grain. Maintain a wet edge when painting. Thick coats wrinkle when
dry. Avoid bubbles. Lightly sand between coats if necessary with
fine sandpaper. Allow 12 to 24 hours to dry between coats. Low
temperatures and humid conditions prolong the drying time. Apply
second and subsequent coats only after previous coat has thoroughly
dried. Do not use below +10 C and or above 80% humidity, in cold
damp conditions, when condensation, rain, dew or frost are
likely to occur or hot days, direct sunlight or hot surfaces.
Provide adequate ventilation during application and drying. Reaches
maximum durability after 8-14 days.
RE-COATING - exterior: Re-coating is recommended after
approximately 2 or 3 years, depending on the exposure to the
weather.
COLOURS: All colours are intermixable. Slight variations
between lots are possible. Special colours are available on
request. Standard colours are:
- Redwood
- Pine
- Mahogany
-
Green
- Grey
- Teak
- Ebony Black
- Red
- Walnut
- Oak
- White
CLEANING: Clean with BIO Thinner
COVERAGE: 1 Litre covers approx. 10-15 sqm.
PACKAGING: 1 and 4 Litres
INGREDIENTS: Based on modified plant oil, wood oil,
rosin, titanium dioxide, mica, silica, bentone, soya lecithin,
UV-protector, paraffin oil, lemon peel oil, Lead free drying
agents.
STORAGE: Keep tightly sealed in a cool and dry
place. Surface film may develop in opened cans.
PAINT DISPOSAL: Do not pour left over paint down the
drain. Unwanted paint should be brushed out on newspaper, allowed
to dry and then disposed of via domestic waste collection. Let
empty container dry out as well and dispose via recycling
program.
SPECIAL PRECAUTION: Keep away from open flames and out of
reach of children. Do not misuse. Please dispose of used rags in a
sealed metal container. Can spontaneously combust. There is no
manufacturer’s liability for applying this product onto non
compatible paint systems like acrylics, polyurethane, epoxy
finishes etc.
The preceding information is given as a general guide only. Some
variations may occur or be advisable for particular conditions. Our
responsibility for claims arising from breach of warranty,
negligence or otherwise is limited to the purchase price of the
material.
BIO Varnishes are environmental friendly
products. 1/05/2011
BIO Wood Primer
BUY NOW from Online
Store
View PDF
version |
