|
DESCRIPTION: BIO Wood Varnish is a clear varnish. It is
based on natural and non toxic ingredients like renewable plant
oils and resins. The natural and non toxic ingredients are
gentle to the climate and resources. It is a hard, elastic,
semi-transparent varnish for use on timber surfaces exposed to sun
and rain. It is resistant to dirt and moisture.
PROTECTION: Protection against weather and
wood-destroying ultra-violet light. 3 coats are recommended.
Minimum dry film thickness on an even smooth surface: 60 micron,
better 100 micron. Box frames, timber windows, cladding and end
grains must be treated BEFORE INSTALLATION with one coat of BIO
Wood Primer and one coat of BIO Wood Varnish clear. It is
also good practice to prime back surfaces. Reapply once the finish
appears to become dull.
PRIMING: For fungi and insect treatment use BIO WOOD
PROTECTING BORAX. Before painting, wipe off the surplus of Borax
with a damp cloth, otherwise surface residue may inhibit paint
adhesion.
PREPARATION: Prepare surface in accordance with AS 2311
Painting of Buildings. Do not apply coatings to unseasoned or wet
timber. Wood and other surfaces should be well sanded, dry and
cleaned of greasy, waxy and dirty contaminants using BIO Thinner.
Round off sharp edges. Imperfect coats may require complete
stripping before applying BIO products. Hardwoods and other timbers
rich in natural oils, waxes, acids and terpenes should be degreased
using BIO Thinner, because these substances may mix with the
varnish and prolong its drying time. Do not apply on over acrylic,
PUR or epoxy based coatings.
APPLICATION: Stir thoroughly before use with a broad flat
stirrer. Brush thinly and evenly working varnish well into the
grain. Maintain a wet edge when painting. Thick coats wrinkle when
dry. Avoid bubbles. Lightly sand between coats if necessary with
fine sandpaper. Allow 12 to 24 hours to dry between coats. Low
temperatures and humid conditions prolong the drying time. Apply
second and subsequent coats only after previous coat has thoroughly
dried. Do not use below +10 C and or above 80% humidity, in
cold damp conditions, when condensation, rain, dew or frost
are likely to occur or hot days, hot surfaces and direct
sunlight. Provide adequate ventilation during application and
drying. Reaches maximum durability after 8-14 days.
RE-COATING: re-coating is recommended after approximately
2 or 3 years, depending on the exposure to the weather.
CLEANING: Clean with BIO Thinner
COVERAGE: 1 Litre covers approx. 1o-12 sqm.
PACKAGING: 1 and 4 Litres.
INGREDIENTS: Based on modified plant oil, wood oil,
rosin, titanium dioxide, mica, silica, bentone, soya lecithin,
UV-protector, paraffin oil, lemon peel oil, Lead free drying
agents.
STORAGE: Keep tightly sealed in a cool and dry place.
Surface film may develop in opened cans.
PAINT DISPOSAL: Do not pour left over paint down the
drain. Unwanted paint should be brushed out on newspaper, allowed
to dry and then disposed of via domestic waste collection. Let
empty container dry out as well and dispose via recycling
program.
SPECIAL PRECAUTION: Keep away from open flames and out of
reach of children. Do not misuse. Please dispose of used rags in a
sealed metal container. Can spontaneously combust.
There is no manufacturer’s liability for applying this product
onto non compatible paint systems like acrylics, polyurethane,
epoxy finishes etc.
The preceding information is given as a general guide only. Some
variations may occur or be advisable for particular conditions. Our
responsibility for claims arising from breach of warranty,
negligence or otherwise is limited to the purchase price of the
material.
BIO Wood Varnishes clear is an
environmental friendly product.
1/05/2011
BUY NOW from Online
Store
View PDF
version |
