|
DESCRIPTION: A matt interior paint based on natural
and non toxic ingredients. The paint has a pleasant smell and is
available in a range of harmonious colours. For use on interior
surfaces such as plasterboard, solid plaster, concrete and mud
brick. It is not recommended for use on timber or on timber
products such as medium density fibroboard, masonite or
particle-board. Bio Wall Paint breathes, while conventional wall
paints seal off the walls, which can promote mould growth. Bio Wall
Paint HD (Heavy Duty) has been tested by the Department of Defence
according to the Australian Standard AS 1580 for scrub-resistant
and dry hiding power. It is therefore well suited for schools,
restaurants, offices and public buildings with heavy traffic areas.
Suitable for use in wet areas. Bio Wall Paint has no Volatile
Organic Compounds (VOC) and does not contribute to smog and
pollution. It contains no lead, glycol derivates, aromatic
hydrocarbons or styrene compounds.
PREPARATION: Prepare the surface in accordance with
AS 2311 - Painting of Buildings. The surface to be painted should
be smooth, dry and cleaned of greasy and dirty contaminants. New
plaster and concrete can be painted after 6 weeks. Remove stains,
watermarks, soot etc. seal off with a weak solution of shellac:
200-250 grams Shellac per 1 Litre methylated spirit. Old lime and
kalsomine paint must be removed. Oil based and acrylic paint
surfaces – semi gloss or gloss - should be sanded with sandpaper. A
test strip is recommended on already painted surfaces if
compatibility is in doubt.
PRIMING: New, highly absorbent and crumbly surfaces
must be primed with BIO Wall Primer. Alkaline surfaces must be
primed first with a special conventional sealer to prevent
saponification of the paint. Plasterboard jointing cement should be
left for 48 hours before painting.
APPLICATION: Stir thoroughly before use with a
broad flat stirrer. May be brushed, rolled or sprayed. Apply one
thick coat or two thin coats (may be thinned with water 5%-10% to
obtain a smooth flowing consistency). New Gyprock surfaces need two
or three coats initially. Airless spraying requires 200
bar/pressure with a nozzle of 0.28 mm Titan -adjustable- or 0.53 mm
with a fan angel of 50.* If painting Bio wall and ceiling paint on
timber do not use bio wall primer but Bio enamel undercoat with 1
topcoat.
Technical Data:
Components:
- Volume solids: 41
- Spreading rate: 8 - 10sqm per Litre
- Density:
1.60
- Dry Hiding Power: 97.2
- Gloss level at 60/80 degrees 2.3-9.7
DRYING: 2-4 hours at 20-23 C/50-55% Humidity. May
be recoated after about 4-6 hours drying time. Allow 7 days for
film to fully cure before washing. Under cold and damp conditions
allow a longer drying time. Do not use below + 5 C. Wet film
thickness 100 micron, dry film thickness: 41 micron.
COLOURS: Bio Wall Paints are supplied in base white or
deep base.Bio Water Based Colour
Pigments are available in a range of colours. The customer
tints to obtain the required colour, however, because the tint is
not a paint in itself, a maximum of 1 part of tint to 1 part white
is recommended. All tints are inter mixable. The standard colours
are: Red, Blue, Violet, Orange, Golden Ochre, Brown, Ochre, Yellow,
Black, Green. Colours by Nature will mix and match colour charts
for you if desired.
Slight variations between colour lots are possible.
Mixing proportions for 4 Litre white Wall paint:
- 1:100 1%
40 ml of Bio water based colour pigment
- 1:50
2% 80 ml of Bio water based colour
pigment
- 1:20 5%
200 ml of Bio water based colour pigment
- 1:10 10% 400 ml of
Bio water based colour pigment
- 1:1 50% 2000 ml of
Bio water based colour pigment
CLEANING: Use warm, soapy water.
COVERAGE: 1 Litre will covers approx. 8 - 10 sqm. On
concrete and rough surfaces 1 Litre covers approx. 3-5 sqm.
Fire Hazard Indices in accordance with AS 1530.3
- Ignition time in minutes = 0
- Spread of flame in 0 seconds = 0
- Heat evolved in kJ/m2 = 0
- Smoke release-non ignited specimens = 3
PACKAGING: Wall Paint: 250 ml, 1, 4 and 10
Litres. Tints 100 ml, 250 ml and 1 Litre.
INGREDIENTS: Castor oil, resins, lemon oil, talc
(asbestos free), white earth pigments, china clay, iron oxides,
metal pigments, earth pigments, calcium carbonate cellulose,
mineral oil, borax, water, lecithin, free of cadmium,
chromates and lead chromates. For green pigment only the ingredient
chromium oxide (non toxic) is used.
STORAGE: Keep tightly sealed in a cool frost free
place. Seal well after using. Once opened, use as quickly as
possible. Keep out of the reach of children.
PAINT DISPOSAL: Do not pour left over paint down the
drain. Unwanted paint should be brushed out on newspaper, allowed
to dry and then disposed of via domestic waste collection. Let
empty paint container dry out as well and dispose via recycling
program.
The preceding information was prepared by BIO Products Australia
and is given as a general guide only. Some variations may occur or
be advisable for particular conditions. The manufacturer’s
responsibility for claims arising from breach of warranty,
negligence or otherwise is limited to the purchase price of the
material.
BIO WALL PAINT and BIO PIGMENTS are environmental friendly
products.
1/08/2008
BUY NOW from Online
Store
view pdf version
(90k)
| 