|
Range of application: Interior and exterior wood
surfaces. Suitable for OSB and MDF-boards. Not suitable for balcony
floors or other high traffic areas. (Exception: KALDET Wood Stain
colour walnut).
Technical qualities: Decorative, open-pored, water
resistant, permeable to water vapour. Sufficiently pigmented
products are also weather resistant. Accentuates natural wood
grain. German Industrial Norm (DIN) 53 160 certified for colour
fastness when exposed to perspiration and saliva. DIN EN 71 Part 3
certified as suitable for toys. Does not contain protection against
blue-staining fungi.
Full Ingredient declaration: Linseed oil - stand oil -
natural resin ester, linseed oil, iron oxide and mineral pigments,
linseed oil - stand oil, linseed oil — wood oil - stand oil,
micronized wax, orange oil, Isoaliphates, alumina, drying agents
free of lead.
Colours:
- 022 boxwood
- 052 brazil
- 124 country blue
- 042 dark teak
- 102 ebony
- 113 green
- 212 light grey
- 076 oak
- 032 pine
- 082 rosewood
- 122 ultramarine blue
- 062 walnut
Interior Only:
- 022 boxwood
- 002 clear
- 212 light grey
- 012 spruce
- 202 white
All colours are inter-mixable. For exterior surfaces, mix only
suitable for exterior use.
Dilution: SVALOS Thinner No. 222
Application method: Brush (undiluted), spray (5 to 10%
dilution) or dip (up to 20% dilution) at temperatures over 12°C
(54oF) and in dry weather conditions.
VARIATION OF USES:
Coverage: 1 litre undiluted covers approximately 15
to 30 m² . Could be considerably less depending on surface
condition and absorbency. Test coat recommended!
Drying time: At 23 °C (73°F) and 50 % relative humidity
12 —24 hrs. Subsequent coats can be applied after approximately 24
hours. Avoid drying delays by providing good light and ventilation
conditions.
Cleaning up: Clean equipment immediately after use with
SVALOS Thinner No. 222, or LEVO Brush Cleaner No. 997.
Specific gravity: approximately 0.90 g/ml depending on
colour.
Safety advice: The product alone will not undergo
spontaneous combustion. Contains limonene. Keep out of the reach of
children. If swallowed do not induce vomiting: seek medical advice
immediately and show the container or label.
Container sizes: 0.375 lt; 0.75 lt; 2.5 lt; 10 lt; 30 lt;
210 lt (7 x 30 lt).
Disposal: According to locally regulated laws.
Storage: Cool and dry please see label for expiry date.
Close lid tightly when not in use.
Wood: Preparation: Surface must be dry (moisture content
under 15 %), solid, able to absorb, clean and free of resin and
dust. For windows and other dimensionally stable woods, the
moisture content for coniferous woods and tropical deciduous woods
should be below 15% and not exceed 12 % in native deciduous woods.
Pre-treat resin rich woods by brushing with SVALOS Thinner No. 222
and exotic woods with KIROS Thinner No. 710, rub dry.
Interior application: Prime with DUBNO Penetrating
Priming Oil No. 261, removed any excess oil after 20 minutes. Sand
in between after drying. After that, and, depending on the area
covered and the degree of protection needed, 1-3 applications are
required. It is recommended to re-brush the surface 5 to 15 minutes
after each application. Please, pay attention to the drying
times!
Exterior application: The amount off ADAO External Primer
No. 259 depends on the absorbency of the wood. Unabsorbed oil is to
be removed after 20 minutes. Sand before proceeding. Apply three
thin coats of KALDET No. 270 within four weeks. Please, pay
attention to the drying times!
OSB: For preparation follow “Wood” application. Interior
application: 1 coat KALDET Transparent Wood Stain No. 270 and apply
2-3 coats KUNOS Natural Oil Sealer: Surface must be dry,
solid, absorbent, clean and free of dust. Sand surface (180-grain).
Depending on surface requirements, apply 2 - 3 coats of KALDET
Transparent Wood Stain No. 270 thinly.
Renovating Porous surfaces: Rough sawn surfaces can retain
dust and dirt particles out of the environment, making it possible
for porous surfaces fungi to grow if the right climate conditions
exist. The grey to black discoloration can be removed with GLOUROS
Natural Siding and Masonry Cleaner No.1806 and a brush or high
pressure cleaner. Clean old paint coatings and sand. Subsequent
treatment as for first coating. Timely re-staining requires only an
intermediary and/or final coat, while overdue re-staining requires
a complete new start. Strongly weathered surfaces require at least
2 – 3 coatings. Depending upon weather resistance, type of wood,
and colour chosen, maximum re-staining time will vary. Wood that
comes into contact with water should be re-stained regularly.
Renovating Non-Porous surfaces: Pore-clogging coatings
(oil-based paints, lacquers, varnishes, wax coats) must be sanded
or stripped non-porous surfaces to completely remove residue.
Surface must be dry, solid, absorbent, neutral, clean and free of
dust. Follow “Wood” instructions and then observe drying time
carefully for potential absorbency problems
important tips: Stir thoroughly before using. Test coat
recommended. When purchasing more than one container of paint, be
sure that all containers have the same batch number. Remove
possible skin off product. Ensure proper ventilation during
application and drying. With oak or other woods containing
incompatibilities such as tannic acid or dyes, or with sanded,
stripped, pre-treated, or stained wood surfaces, discoloration is
possible within one week. KALDET Transparent Wood Stain No. 270
does not contain fungicides. Rough sawn wood is prone to
blue-staining fungi. Sand rough surfaces. Treat wood prone to
blue-staining fungi and back aired panelling with ADAO External
Primer No. 259. Seams of new windows should be treated with a very
thin coat of KALDET No. 270. Silicone sealant should be applied
only after complete drying, but should not be painted over with
KALDET No. 270. Linseed oil based putty can be painted over after
one day.
In interior areas, the use of wax over a coloured stain can
cause the colour to lighten slightly due to pigment rub-off. Strong
possibility of yellowing for colours white and light grey in low
light conditions. Do NOT paint over the colours white or light grey
with KALDET Transparent Wood Stain clear or any other LIVOS oil, as
surface may yellow.
View pdf
version
These directions are the
result of long years of research and practical testing. They are
backed by our most current expert information. New findings may
invalidate this information. This data sheet is meant to serve as
information and instruction. No legal liability should be
interpreted from it. In case of doubt, please contact the retailer,
wholesaler, or manufacturer. |
